In today?s society there is an increasing demand for renewable energy sources such as sun and wind power. These sources are intermittent, and energy storage is therefore needed to ensure a constant power supply. This report compares pumped hydro energy storage (PHES), compressed air energy storage (CAES), flywheels, batteries, super magnetic energy storage (SMES) and hydrogen energy storage.The opportunities for further development are limited for PHES and CAES in comparison with the other technologies. Lithium-ion batteries and hydrogen energy storage are considered to have the most potential in the future.

Design of a house requires knowledge of both technology and economics. Heating and ventilation shall be designed, costs are calculated and estimated and requirements must be fulfilled. Which heating system is to be elected is also a difficult choice, especially with rising energy prices as a factor.The choice of energy system is not always given, because it depends on several factors. Below is a comparison between district heating, geothermal heat pump and electric boiler from an economic standpoint. In a previous report appears district heating and geothermal heat pump as the best options.

Results have shown that flow batteries may be a solution in the future as an effective and environmental friendly method to an energy storage system (ESS). The technology is reliable and has a high efficiency that comes with low energy losses and a long lifetime. The range of possible fields is suitable for cutting energy peaks in the power grid, by always have a ready and available energy storage that balances the production. By comparing the advantages of flow batteries with conventional batteries it is mainly the fact that they can conserve energy for a long time without being self-discharged thanks to that the storage capacity is in principle endless and limited by the size of the electrolytes tanks that makes them a great energy storage system. The batteries won?t take any damage or decrease in performance when charging or discharging it or if you exhausts it to 100 % and leave it discharged for a long time.

In this work an assessment of the compressed air system in the facilities of Vattenfall Heat Uppsala has been conducted. The facilities constitutes, among others, a combined heat and power plant, and two waste incineration plants. The compressed air is supplied primarily by seven rotary screw compressors and yearly electric energy consumption in these has been determined. Furthermore, the usage of compressed air has been mapped in order to find processes with energy savings potential. Several suggestions how to reduce the usage of compressed air have been presented, resulting in decreased need of electric energy and reduced CO2-emissions.The results show that total need of electric energy in the compressors, during a standard production year, amounts to 5.83 GWh.

Latent heat storage is a way to store thermal energy when a phase change material undergoes a phase change. The advantage of latent heat storage is the capability to store more energy per mass unit than other heat storage methods. The most commonly used phase change in latent heat storage is the transition between solid and liquid. Phase change materials can be divided into organics, inorganics and eutectics.In the Nordic electricity market the price of electricity is set every hour by Nordpool spot, which leads to price fluctuations because of changes in demand. The main goal of this report is to create a latent heat storage system in a single-family home and investigate the possibility to save money by charging the latent heat storage system when the price of electricity is low, and discharge when the price is high.The thermodynamic model consisted of a ?tube-in-tube? heat exchanger with phase change material in the outer tube and water as the heat transfer fluid in the inner tube.

Humanity stands before a huge challenge to lower its emissions of carbon dioxide and its use of energy at the same time as the global population is rising and the developing countries are being industrialized. A lot of newly built buildings are due to this challenge, designed to be more energy efficient but also use renewable energy resources instead of pollutant fossil fuels .Solar energy is one of the purest forms of energy that exists in abundant amounts, which is why it is most likely that it could come to play a major part in the future energy market. The main purpose of this report is to investigate the possibility to implement a sustainable energy system with solar thermal heat and  heat storage as main sources of energy in the neighborhood ?kvarteret Lagern?, which is the area where the old football stadium ?Rasunda Stadion? was located. New developments within different heat storage techniques have opened up new approaches to enable buildings an all year round heat supply from solar energy. This report will focus on heat storage in boreholes. At the present here is only a preliminary plan of how the neighborhood is supposed to be designed.

Micro-power wind energy convertors have recently increased in popularity. The reasons for this are among other things the increasing cost of electric energy and enviromental concern.In this thesis the connection of these micro-power wind energy convertors to the utility network is discussed. Electric standards for the connection of small production units is presented. Finally some calculations and measurements of electric quality are also presented. The utility network used in the calculations is part of Halmstad Energi och Miljö network..

Norconsult AB has developed a solarhousing concept, a house designed for the warm climate in the Middle East andwith large quantities of solar panels installed. The cooling system for the house was designed in an earlier report, the purpose of this thesis is to investigate the possibility of short and long term storage of thermal energy via an underground energy storage volume.Two different designs of the storage and three different filling materials have been integrated into a model to simulate different cases. The first design consisted of pipes installed in the ground, without insulation. The second design consisted of an insulated concrete box installed to prevent thermal energy from the surrounding soil to flow towards the lower temperature regions within the storage. The three different filling materials were dry saudi sand, water saturated saudi sand and the filling material used by the client for energy storage in Sweden.The results from the simulations show that neither of the designs, regardless of the filling material, managed to extract enough thermal energy from the house to the ground to uphold the demands of indoor climate.

Most of the portable electronic devices use a battery as a primary power source. Nowadays, when the applications are becoming smaller and smaller and more power efficient, the designer needs to concentrate more on reducing power consumption, using secondary power sources and introducing power storage devices. Multiple power source availability and a power storage device on the board will make the applications much more useful and efficient in everyday use. This thesis proposes a power supply unit (PSU) for wireless sensor platforms which is capable of supplying a sensor node with energy from multiple sources, as well as status information from the PSU. Present power storage devices, like electric double-layer capacitors (EDLCs) and batteries, have become more and more common as their characteristics have developed.

To achieve the goal of fossil independency in the Swedish vehicle fleet in 2030, it would be important to substantially increase the proportion of electric vehicles, both BEV:s (Battery Electric Vehicles) and PHEV:s (Plug-in Hybrid Electric Vehicles). The Swedish Energy Agency has funded numerous research and development projects about electric vehicles in recent years. An important task for the Swedish Energy Agency is to allocate state funds to those projects with the greatest potential to contribute to increased establishment of electric vehicles in society. The purpose of this work is mainly to understand the efforts and measures that can make the market for electric vehicles to grow. The report can contribute to a better understanding of how far the research on electric vehicles has come and what has to be done in the future to promote the establishment of electric vehicles. Another aim for this report is that it should serve as a basis for future decisions by the Swedish Energy Agency on which projects that will be funded with state funds.

With gas prices persistently rising, electric and hybrid vehicles are getting more and more common and in recent years several new electric cars have evolved on the market. Although the energy consumption and low emissions are a huge benefit of the electric cars, they inevitably suffer from high prices, short range and time consuming recharging periods. To be able to withstand the competition it is important that electric vehicles not only can withstand general were and tare, but also the harsh conditions that ordinary cars is exposed to in daily usage. The purpose of this project is to develop a test methodology which replicate situations that could appear in daily usage of electric or hybrid cars and to understand the problems related to usage of electric cars in winter conditions. This paper also discusses the major differences between hybrid cars and electric cars.

The fishing port of Bläsinge is located on the east coast of Öland, Sweden?s second largest island. Today the port has a limited supply of freshwater. The economic association of the fishing port wants to expand their business, so that they will also include tourist services. To do this the harbor will need a more independant source of freshwater, with a higher quality than the present well.

The energy sector is facing an impending paradigm shift. Today?s technology enables the end-user to generate their own energy locally at home. Furthermore, recently developed storage technologies make it possible to balance energy demand with stored energy and integrate district heating with the local power grid. This means that in the future heat and electric power will interact and energy flows is converted over energy boundaries.

sustainable development by reducing the energy use by EU:s directive of energy efficiency and the UN Convention. The second purpose is to present the technical solutions regarding ventilation and heating system that is being used in passive houses. This was done using 8 passive houses, 4 germany and 4 swedish passive houses. Even the international and Swedish system requirements for passive houses have been addressed in this project. The goal was also to explain how and why the mechanical system in passive houses has developed to the technology used today.

The constant need of energy is something that affects us all no matter our current situation. Whether we are driving our car to work, taking the elevator or using the oven to cook dinner we end up relying on energy. Our whole society is continuously striving to achieve a higher grade of efficiency and the process of supplying ourselves with energy is no exception. The importance of appliances in our everyday life cannot be exaggerated and thus the importance of their high efficiency.Efficiency is already a keyword in the appliance industry with labels, stars and numbers helping us choosing the most suitable option for the task ahead. No matter how efficient appliances often use pure electricity as their energy source.